|
|
 |
 |
|
CFR-1220T |
CFR-1220F |
CFR-1220D |
| Effective stroke |
Y=1,200mm,X=2,000mm |
| Motorization |
X, Y, Z, θ 4 axes DC software servo |
| X, Y, θ timing belt motorization |
| Maximum plotting speed |
30cm/SEC |
| Maximum acceleration |
0.3G |
| Work fixation |
Air suction by a blower
(Suction area can be divided into 4: left front, left rear, right front, and right rear by clump lever.) |
| Head |
A:pen/swivel cutter(max:200g) |
A:pen/swivel cutter(max:200g) |
A:pen/swivel cutter(max:200g) |
| B:tangential cutter(max:1,500g) |
B:tangential cutter(max:5,000g) |
B:tangential cutter(max:10,000g) |
| C:reciprocal cutter(max:5,000g) |
C:reciprocal cutter(max:5,000g) |
C:reciprocal cutter(max:5,000g) |
| Mechanical resolution |
X, Y=3.125µm θ=0.05625º |
| Command resolution |
0.025mm/0.01mm
(changeable from operation panel) |
| Accuracy |
Distance accuracy |
±0.1mm or ±0.1% whichever is greater |
| Perpendicularity |
1.0mm |
| Repetition |
0.3mm |
| Origin repetition |
±0.1mm |
| Compression air |
6kgf/cm2 more than 300l/min (dryer required) |
| Maximum size of set work |
1,440mm x 2,500mm x 65mm |
| Maximum weight of set work |
70kg MAX (load even distributed) |
| Receiver buffer size |
1MB |
| Command |
MGK-II C3 |
| Interface |
RS-232C |
| Power requirement |
Plotter:AC100V 50/60Hz Blower:3 phase AC200V 50/60Hz |
| Power consumption |
Plotter:500VA Blower:3 phase AC200V 50/60Hz |
| Operation environment |
10~35ºC 35~75% No condensation |
| Dimension(legs are exception) |
2,005(W) x 2,668(D) x 666(H) mm |
| Dimension when safety barrier attached |
2,105(W) x 2,668(D) x 1,300(H) mm |
| Plotter weight |
295kg |
| Safety barrier weight |
30kg |
| Blower weight |
70kg |
| Safety measure |
Safety barrier is equipped on X axis side.
An area sensor is equipped above the barrier. |
*A, B, C tools can be used together when the work is less than 15mm thickness.
*A and C tools can be used together when the work is more than 15mm thickness. |
|
CFS-1313 |
| Motor |
DC servo motor, software servo control |
| Effective area |
1,250mm x 1,250mm |
| Maximum plotting speed |
20cm/sec (all direction) |
| Maximum acceleration |
Cut:0.1G MAX Print:0.2G MAX |
| Mechanical resolution |
0.005mm(X, Y axes) 0.02º(θ axis) |
| Command resolution |
0.025mm/0.010 (changeable from operation panel) |
| Accuracy |
Distance accuracy |
Less than ±0.1mm |
| Perpendicularity |
Less than ±0.1mm or ±0.1% whichever is greater |
| Repetition |
X, Y axes:less than ±0.2mm θaxis:less than 0.5º |
| Origin repetition |
0.8mm (all effective area) |
| Work fixation |
Mecha clump, air suction, etc |
| Compression air |
More than 6kgf/cm2, 50L/min required |
| Maximum size of set work |
Table size 1,720(W) x 1,400(D) x 30(H) mm |
| Maximum weight of set work |
100kg (load even distributed) |
| Motorization |
X, Y axes: form rolling ball screw Z axis:air cylinder, rack and pinion jack |
| Command |
MGL-IIC |
| Receiver buffer size |
1MB |
| Operating environment |
Temperature |
5~40°C |
| Humidity |
35~75%(Rh) No condensation |
| Dust |
Normal office |
| Interface |
RS-232C |
| Power requirement |
AC100V±10% 50/60Hz |
| Power consumption |
Plotter |
1000VA |
| Blower |
850VA(during air suction) |
| Dimension |
1,720(W) x 1,860(D) x 1,240(H) mm |
| Head height |
705mm |
| Weight |
250kg |
|
Low pressure tangential head |
High pressure tangential head |
Pen head |
| Composition |
DC servo motor |
Air cylinder (air regulator) |
Moving coil+air cylinder (current control) |
| Pen |
- |
- |
Oil-base ball point pen |
| Cutter |
Both-bladed cutter |
One-side-bladed cutter |
Swivel cutter |
| Maximum blade-down distance |
10mm (guilder A) |
6mm (guilder B) |
- |
| Blade-down resolution |
0.05mm |
- |
| Stroke |
40mm from cutting surface |
6mm from cutting surface |
41mm from cutting surface |
| Pressure |
300~1,500g |
1000~25,000g |
20~100g (5g step)
100~200g (10g step) |
| Pressure setting |
Auto (by operation or command) |
| Number of response (*3) |
2 /sec |
1 /sec |
16 /sec (air cylinder operation is exception) |
| Head height adjustment |
Not available |
0~20 |
|
|
|
